Pettit EZ Decks Non Skid Paint

Pettit EZ Decks Non Skid Deck PaintThe state-of-the-art Pettit EZ Decks non-skid deck paint adds a powerful finish that the weather simply cant penetrate. It stays durable for years and is very simple to apply. Part of its secret lies within its special grit that produces a durable, slip-resistant finish applicable to all decks and cabin soles. As with other select Pettit EZ products, Pettit EZ Decks allows for a seamless way to achieve maximum results with little-to-no effort.The durable weather-resistant finish helps to prevent long term abrasions and abuse. Comes loaded with ultraviolet filters to combat fading while offering premium color retention that will stay vibrant for years without cracking like lesser deck finishes. Available in three popular colors that match perfectly with Pettits Easypoxy topside enamel.Features:Provides a super tough non-skid finishExtremely durable weather-resistant finishFade and UV resistant, colors hold up under tough conditionsEZ decks is simple to use and easy to applySold in QuartsAssociated Products:Pettit Brush Thinner- For brushing and clean upPettit Spray Thinner-For spraying applicationPettit Bio-Blue -For preparing bare fiberglass surfaceSpecifications:Finish: High GlossCoverage:600 sq. ft/gal.Number of Coats:2 MinimumHow To Apply Pettit EZ Decks Non-Skid PaintStir EZ Decks thoroughly before use, as the non-skid agent in the paint will float to the surface in the container. This paint can be applied by brush or roller; if applying by brush or roller, apply without thinning. If applying in hot weather, 5-10% of Pettit 120 Thinner may be added to maintain a wet edge. For best results on large surfaces, roll out using a short nap or foam roller followed immediately by leveling off with the tip of a brush.Application Method: Brush or roller Number of Coats:2 minimum Dry Film Thickness per Coat:1.5 mils (2.6 wet mils)Coverage:600 sq. ft/gal. Application Temp: 50F Min. / 90F Max.Thinner: 120 Brushing Thinner (clean up also)DRY TIMES:TempTo TouchTo Recoat90F1-1/2 Hours8 Hours70F3 Hours16 Hours50F6 Hours24 HoursApplication SystemsBare WoodSand surface smooth with 80-120 grit sandpaper, then solvent clean with Pettit 120 Thinner to remove residue.Fill all screw heads or small holes with an epoxy fairing compound; sand flush and solvent clean.Apply a coat of 2018 Clear Sealer to penetrate and seal the porous grain.Follow with one or two coats of 6149 Easypoxy White Undercoater until an evenly smooth base condition is reached.Sand each coat with 80-120 grit sandpaper and solvent clean with Pettit 120 Thinner.Proceed with the first finish coat of EZ Decks.Bare SteelSurface must be cleaned to a bright finish by sandblasting or grinding. Remove blast residue.Immediately apply one coat of 6980 Rustlok Primer. Allow to dry until tacky.If surface is rough, apply a coat of 6627 Tie-Coat Primer. Sand well and solvent clean.Repeat application as needed until a smooth, uniform base is reached.Proceed with the first coat of EZ Decks.Bare AluminumWipe the surface free of oil and grease with Pettit 120 Thinner.Remove oxidation and etch the surface with medium grit emery cloth. Remove sanding residue.Apply one thin “wet” coat of 6455/044 Metal Primer. Allow to dry at least two hours.Proceed with the first coat of EZ Decks.6149 Easypoxy White Undercoater can be used over the 6455/044 Metal Primer for smoothing surfaces if desired.Bare FiberglassThe entire surface being painted must be thoroughly washed with 120 Thinner or 92 Bio-Blue.Sand the gel coat with 80 to 120 grit sandpaper to a dull, frosty appearance. Solvent clean to remove residue.If the surface is in excellent condition, proceed with the fi